Skip to the catalogue sheet
Seating · sheet L3 · five parts of a drawing set

Lounge seating, low and deep

L3Bent plywood, woven wool, nothing else.

Two pressed birch loops, one moulded shell, two ash rods and a pair of wool cushions. Each part is flat enough to stand against a wall; together they make a chair you sink into rather than sit on.

720WIDTH, MM
800DEPTH, MM
740HEIGHT, MM
Side elevation of the L3 chair: a closed loop of bent plywood forms runner, front leg and armrest; a moulded shell carries a dark seat cushion and a reclined back cushion. Dimension lines give 800 millimetres of depth and 740 of height.
Fig. 1 — Side elevation, near frame shownLetters refer to the parts list

Seven parts, laid flat

Every piece is drawn as it would come off the press or the loom, before it meets the others. Nothing is glued to anything else once the parts leave the workshop.

ALeft frame

Side loop, near hand

One continuous band of eleven birch veneers: runner, front post, arm and rear stay in a single closed line.

BRight frame

Side loop, far hand

The mirror of A, pressed on the same form turned over. Two routed grooves on the inner face take the shell.

CShell

Seat and back in one

A single sheet bent twice: a rolled front lip, a shallow seat pan and a back leaning 18 degrees past upright.

DFront rod

Low front stretcher

Turned ash with a stepped end on each side. It passes through both loops and holds them square.

ERear rod

Low rear stretcher

Identical to D except for a centre hole, where a wool strap from the back cushion is tied off.

FSeat pad

Seat cushion

A layered wool-batting pad in a woven cover, piped along the front edge where the knees rest.

GBack pad

Back cushion

Hangs over the top of the shell by two loops of the same cloth and is held at the foot by the strap to E.

Order of assembly

A + B→D + E→C→F + G

Rods through the loops, shell slid down the grooves until it stops, cushions laid in and tied. No screws are planned anywhere in the chair.

Three elevations

Front, side and plan at one common scale. Blue carries the measurements, dashed lines are edges hidden behind nearer parts, the long chain line is the centre.

Front elevation: two narrow frame edges 720 millimetres apart, the seat cushion face between them, the back cushion rising behind, and the front rod low down. 720 560
Frontarm height 560
Side elevation: the plywood loop, the bent shell, and both cushions, with 800 millimetres of depth, 740 of height and a seat height of 380. 800 740 380
Sideseat height 380
Plan from above: two frame bands 800 millimetres long, the seat cushion between them, the back cushion at the rear, and the two rods shown dashed beneath the seat. 720 800 FRONT ↓
Planfront at the foot of the sheet

dimension, millimetreshidden edgecentre line

One bent line

The frame is not cut from a board. It is built up from thin veneers and pressed around a form until the glue sets and the curve stays.

Section through the bend: eleven thin veneers, alternating in grain direction, curve around a solid form and are held by clamps. 11 veneers about 1.5 mm each Grain alternates black along, blue across Form solid beech, reused Clamp line pressure held overnight

Bending thin wood is older than any of the chairs that made it famous, and it still rewards patience more than force. A loop pressed this way keeps its shape because every layer is locked to the next, with the grain turned a quarter at each glue line.

The L3 frame would use the same form for both sides. Only the grooves differ, cut after pressing, so a left loop and a right loop start their lives as identical blanks.

  1. Veneers cut oversize, grain marked on each sheet.
  2. Glue rolled on, stack laid over the form in alternating directions.
  3. Clamped along the whole line and left to cure.
  4. Released, trimmed to width, edges eased and oiled.

Six cloths

Covers in a close twill of wool, fulled after weaving so the cut edge holds. Dyed yarns sit beside the undyed ones.

  • UltramarineW-01 · dyed twill
  • CoalW-02 · dyed twill
  • UndyedW-03 · natural fleece
  • SlateW-04 · mixed yarn
  • NightW-05 · dyed twill
  • OatW-06 · plain weave

The cloth is chosen to age with the frame: birch darkens toward honey, and the wool softens and pills a little at the arms. Covers slide off the pads and can be swapped between colours without tools.

Weave
2/2 twill, fulled; oat is a plain weave
Weight
around 600 g per square metre
Pad
layered wool batting over a coir core

Figures

The numbers the drawings were made to. Any real prototype would nudge most of them.

Width
720mm
Depth
800mm
Height
740mm
Seat height
380mm
Arm height
560mm
Back angle
18° past upright
Weight
14kg, estimated
Parts
7
Frame and shell
Pressed birch veneer, oiled; ash rods
Cushions
Wool twill cover, wool batting, coir core

Measured from the floor to the top of the uncompressed cushion. Figures read left to right, front elevation first, as on the drawings above.

Low, deep, and quiet about it.

A chair for the corner by the window, for a long book or no book at all. The frame does the holding; the wool does the rest.